| |

NASA Launches Unmanned Artemis Rocket for Moon Mission

NASA ArtemisLaunch400x275

November 16, 2022

By NASA News Release

Following a successful launch of NASA’s Space Launch System (SLS), the most powerful rocket in the world, the agency’s Orion spacecraft is on its way to the Moon as part of the Artemis program. Carrying an uncrewed Orion, SLS lifted off for its flight test debut at 1:47 a.m. EST Wednesday from Launch Pad 39B at NASA’s Kennedy Space Center in Florida.  

The launch is the first leg of a mission in which Orion is planned to travel approximately 40,000 miles beyond the Moon and return to Earth over the course of 25.5 days. Known as Artemis I, the mission is a critical part of NASA’s Moon to Mars exploration approach, in which the agency explores for the benefit of humanity. It’s an important test for the agency before flying astronauts on the Artemis II mission

“What an incredible sight to see NASA’s Space Launch System rocket and Orion spacecraft launch together for the first time,” said Bill Nelson, NASA Administrator. “This uncrewed flight test will push Orion to the limits in the rigors of deep space, helping us prepare for human exploration on the Moon and, ultimately, Mars.”

After reaching its initial orbit, Orion deployed its solar arrays and engineers began performing checkouts of the spacecraft’s systems. About 1.5 hours into flight, the rocket’s upper stage engine successfully fired for approximately 18 minutes to give Orion the big push needed to send it out of Earth orbit and toward the Moon.  

Orion has separated from its upper stage and is on its outbound coast to the Moon powered by its service module, which is the propulsive powerhouse provided by ESA (European Space Agency) through an international collaboration. 

“It’s taken a lot to get here, but Orion is now on its way to the Moon,” said Jim Free, NASA deputy associate administrator for the Exploration Systems Development Mission Directorate. “This successful launch means NASA and our partners are on a path to explore farther in space than ever before for the benefit of humanity.”

Over the next several hours, a series of 10 small science investigations and technology demonstrations, called CubeSats, will deploy from a ring that connects the upper stage to the spacecraft. Each CubeSat has its own mission that has the potential to fill gaps in our knowledge of the solar system or demonstrate technologies that may benefit the design of future missions to explore the Moon and beyond. 

Orion’s service module will also perform the first of a series of burns to keep Orion on course toward the Moon approximately eight hours after launch. In the coming days, mission controllers at NASA’s Johnson Space Center in Houston will conduct additional checkouts and course corrections as needed. Orion is expected to fly by the Moon on Nov. 21, performing a close approach of the lunar surface on its way to a distant retrograde orbit, a highly stable orbit thousands of miles beyond the Moon.  

“The Space Launch System rocket delivered the power and performance to send Orion on its way to the Moon,” said Mike Sarafin, Artemis I mission manager. “With the accomplishment of the first major milestone of the mission, Orion will now embark on the next phase to test its systems and prepare for future missions with astronauts.”  

The SLS rocket and Orion spacecraft arrived at Kennedy’s Launch Pad 39B on Nov. 4 where they rode out Hurricane Nicole. Following the storm, teams conducted thorough assessments of the rocket, spacecraft, and associated ground systems and confirmed there were no significant impacts from the severe weather.

Engineers previously rolled the rocket back to the Vehicle Assembly Building (VAB) Sept. 26 ahead of Hurricane Ian and after waving off two previous launch attempts Aug. 29 due to a faulty temperature sensor, and Sept. 4 due to a liquid hydrogen leak at an interface between the rocket and mobile launcher. Prior to rolling back to the VAB, teams successfully repaired the leak and demonstrated updated tanking procedures. While in the VAB, teams performed standard maintenance to repair minor damage to the foam and cork on the thermal protection system and recharge or replace batteries throughout the system. 

NASA said Artemis I is supported by thousands of people around the world, from contractors who built Orion and SLS, and the ground infrastructure needed to launch them, to international and university partners, to small businesses supplying subsystems and components.  

Through Artemis missions, NASA said it will land the first woman and the first person of color on the surface of the Moon, paving the way for a long-term lunar presence and serving as a stepping stone for astronauts on the way to Mars.


Robotics World News

  • Raise Robotics Raises $2.2M in Seed Round Funding

    Raise Robotics Raises $2.2M in Seed Round Funding

    Raise Robotics, which develops robotic equipment for construction sites, has announced it raised $2.2 million in a pre-seed funding round (reported by Construction Dive). The company is currently providing fenestration and mass timber contractors with semi-autonomous equipment that completes bracket layout, installment and verification four times faster than standard methods. “Our mission at Raise is… Read More…

  • Scythe Robotics Raises $42M for Commercial Autonomous Mower

    Scythe Robotics Raises $42M for Commercial Autonomous Mower

    Colorado-based Scythe Robotics, which develops advanced commercial-grade autonomous systems for professional landscapers, has announced it raised $42 million in Series B funding. The company said it will use the funding to help meet demand for more than 7,500 reservations for its fully electric, fully autonomous M.52 mower. With the latest financing, Scythe Robotics has raised… Read More…


Products for Robots & Cobots

  • Celera Motion Introduces the World’s Smallest Servo Drives

    Celera Motion Introduces the World’s Smallest Servo Drives

    Celera Motion, a business unit of Novanta Inc., announced the launch of two of the world’s smallest servo drives, the Denali Series. Denali is the latest addition to Celera Motion’s line of premium-performance Ingenia servo drives. Denali offers hardware architecture as well as optimized power management, with a minimum standby power consumption of down to 1.2 W. The servo drives… Read More…

  • Heiland Electronics Introduces Mini I/O Connectors for Fast Speeds and Easy Field Installs

    Heiland Electronics Introduces Mini I/O Connectors for Fast Speeds and Easy Field Installs

    Heilind Electronics, a leading global distributor of electronic components and authorized distributor for TE Connectivity, offers the Mini I/O Cat6A connector as part of its full line of TE ethernet products. TE Industrial’s Mini I/O connectors eliminate the need for special tools to create a fast and secure wire-to-wire or wire-to-board connection. The mini I/O… Read More…